Thread length : Short thread is suitable for opening holes in thin boards or devices with internal threads, long thread is suitable for joining thick boards, and extended thread can be customized.
Waterproof Brass Cable gland are available in a full range of specifications, with high tensile strength, and are waterproof, dustproof, salt spray-proof, and resistant to acid, alkali, alcohol, grease, and general solvents. Its brass parts are precision-machined using advanced CNC machine tools, with excellent craftsmanship to ensure the high precision of each product.

As a supporting product for cables, this metal Brass Cable gland can fix the cable by locking it at one end, and enter the device through the junction box at the other end, or select a threaded entry line according to the internal thread of the electrical equipment. The connector body is made of nickel-plated brass, the clamping parts are made of nylon plastic, and the seals and O-rings are made of nitrile rubber. The surface is smooth and bright, with good pressure resistance and toughness, no odor, and waterproof, rust-proof, corrosion-resistant, and excellent performance. Brass Cable gland are tightly connected, have strong electrical conductivity, and are easy to assemble and save time.

Waterproof Brass Cable gland are widely used, have high tensile strength, and are suitable for a variety of harsh environments. They can ensure the normal connection and transmission of cables in waterproof, dustproof, salt-proof, acid-alkali-resistant and various chemical solvent environments. With the expansion of the scope of application, waterproof Cable gland are widely used both indoors and outdoors. When laying cables, disconnected lines need to be reconnected. Traditional connectors have no waterproof function, high maintenance costs and insufficient safety. To solve this problem, we developed connectors with waterproof function to ensure that cables can still be stably connected and transmitted in harsh environments.
Parameter table
Metric thread type
| Model | Thread AG | Cable Range (mm) | Thread O.D (mm) | Mounting Hole Diameter(mm) | Thread length GL(mm) | Bonding length (mm) | Spanner Size (mm) |
| M14-NP | M14×1.5 | 8-4 | 14 | 14-14.2 | 7 | 19 | 17 |
| M16-NP | M16×1.5 | 8-4 | 16 | 16-16.2 | 8 | 20 | 18 |
| M18-NP | M18×1.5 | 10-5 | 18 | 18-18.2 | 8 | 21 | 20 |
| M20-NP | M20×1.5 | 12-6 | 20 | 20-20.2 | 8 | 22 | 22 |
| M22-NP | M22×1.5 | 14-10 | 22 | 22-22.2 | 8 | 23 | 24 |
| M24-NP | M24×1.5 | 14-10 | 24 | 24-24.2 | 9 | 25 | 24/27 |
| M25-NP | M25×1.5 | 14-10 | 25 | 25-25.2 | 9 | 25 | 24/27 |
| M28-NP | M28×1.5 | 18-13 | 28 | 28-28.2 | 9 | 27 | 30 |
| M30-NP | M30×1.5 | 18-13 | 30 | 30-30.2 | 9 | 29 | 30/32 |
| M32-NP | M32×1.5 | 22-15 | 32 | 32-32.2 | 10 | 29 | 35 |
| M33-NP | M33×1.5 | 22-15 | 33 | 33-33.2 | 10 | 29 | 35 |
| M36-NP | M36×1.5 | 25-18 | 36 | 36-36.2 | 10 | 31 | 40 |
| M37-NP | M37×1.5 | 25-18 | 37 | 37-37.2 | 10 | 31 | 40 |
| M40-NP | M40×1.5 | 25-18 | 40 | 40-40.2 | 11 | 31 | 40/45 |
| M42-NP | M42×1.5 | 30-22 | 42 | 42-42.2 | 11 | 35 | 45 |
| M48-NP | M48×1.5 | 33-25 | 48 | 48-48.2 | 11 | 37 | 50/52 |
| M50-NP | M50×1.5 | 38-32 | 50 | 50-50.2 | 12 | 37 | 57/55 |
| M63-NP | M63×1.5 | 44-37 | 63 | 63-63.2 | 13 | 38 | 64/68 |
PG thread type
| Model | Thread AG | Cable Range (mm) | Thread O.D (mm) | Mounting Hole Diameter(mm) | Thread length GL(mm) | Bonding length (mm) | Spanner Size (mm) |
| PG7-NP | PG7 | 6.3-3 | 12.5 | 12.5-12.7 | 7 | 19 | 14 |
| PG9-NP | PG9 | 8-4 | 15.2 | 15.2-15.4 | 8 | 20 | 18 |
| PG11-NP | PG11 | 10-5 | 18.6 | 18.6-18.8 | 8 | 21 | 20/21 |
| PG13.5-NP | PG13.5 | 12-6 | 20.4 | 20.4-20.6 | 8 | 22 | 22 |
| PG16-NP | PG16 | 14-10 | 22.5 | 22.5-22.7 | 9 | 23 | 24 |
| PG19-NP | PG19 | 14-10 | 25 | 25-25.2 | 9 | 25 | 24/27 |
| PG21-NP | PG21 | 18-13 | 28.3 | 28.3-28.5 | 9 | 27 | 30/32 |
| PG25-NP | PG25 | 22-15 | 32 | 32-32.2 | 10 | 29 | 35 |
| PG29-NP | PG29 | 25-18 | 37 | 37-37.2 | 11 | 31 | 40 |
| PG36-NP | PG36 | 33-25 | 47 | 47-47.2 | 12 | 37 | 50 |
| PG42-NP | PG42 | 38-32 | 54 | 54-54.2 | 13 | 38 | 57 |
| PG48-NP | PG48 | 44-37 | 59.3 | 59.3-59.5 | 14 | 38 | 64 |
| PG63-NP | PG63 | 52-42 | 72 | 72-72.2 | 15 | 42 | 78 |
Specification, sealing and ordering
How to read the parameter table above
| Column | What it tells you | What to check before ordering |
|---|---|---|
| Model | Thread system and size, for example M20 or PG13.5 | Must match the hole already punched or planned in the enclosure |
| Thread AG | Actual thread specification, including pitch | Pitch decides whether an existing locknut or thread adapter will fit |
| Cable range | The sheath diameter the seal will grip and seal | Your cable OD must sit inside the range, not on its limit |
| Thread O.D. | Outside diameter of the thread | Drives the hole size: hole equals thread O.D. plus about 0.2 mm |
| Mounting hole | Recommended panel hole for that size | Larger and the washer will not seal; smaller and the thread will not enter |
| Thread length GL | Thread length available through the wall | Must exceed panel thickness plus locknut and washer |
| Spanner size | Wrench across flats for body and nut | Confirms you can torque it in the space available |
IP rating: what this gland is tested to
The nickel-plated brass body is rated IP68 and IP69K depending on the seal set specified. IP68 covers continuous immersion and IP69K covers high-pressure, high-temperature jet cleaning, and the two are not interchangeable: a gland that passes one does not automatically pass the other. Tell us which exposure applies and the seal set is matched to it.
We publish IP68 in written grades rather than one label: 1.5 m for 30 minutes, 2 m for 24 hours as standard, 5 m for 72 hours for marine and tunnel work, 10 m for 168 hours by special order. The rating holds only if the gland is installed on a cable inside its clamping range and torqued to the datasheet value.
Installation sequence
- Check the thread, hole and cable OD against the parameter table before opening the enclosure.
- Fit the body through the hole with its sealing washer, then tighten the locknut. Where an earth tag is used, it sits under the body, not over the washer.
- Pass the cable through the dome nut and the sealing insert. Strip the sheath only if the design calls for it; the seal works on the sheath, not on the conductors.
- Seat the insert so the sheath sits inside the stated clamping range, then tighten the dome nut by hand and finish to the torque on the datasheet.
- Verify by pulling and rotating the cable by hand, and by checking that the seal is evenly compressed with no insert extruded from its housing.
Torque figures depend on size and material, so they are published on the datasheet rather than in a general guide. The acceptance criterion is the result, not the number on the wrench.
Where this gland is used
- Machine tools, pumps and compressors where vibration would work a plastic entry loose
- Industrial enclosures, HVAC plant and outdoor cabinets on coated steel structures
- Armoured and screened cable entries where an earth tag is required
- Washdown areas, using the IP69K seal set rather than the standard one
Nickel plating gives corrosion resistance on the body, but the thread is still brass underneath. For coastal, chemical or continuously wet service, stainless steel is the more economical answer over the life of the installation.
Cable gland price range by type
Buyers usually shortlist a gland family before a final size and drawing are fixed, so the table below gives the indicative price band for each family we produce. It is a budgeting reference, not a quotation: within one family the price moves with thread system, cable range, seal material and the documentation package requested.
| Gland Type | Typical Material | Waterproof Rating | Typical Application | Indicative Price (FOB, USD/pc) |
|---|---|---|---|---|
| Standard single-compression nylon | PA66 nylon | IP54 – IP66 | Control panels, indoor junction boxes, general machinery | $0.11 – $0.21 |
| Waterproof double-seal nylon | PA66 nylon | IP68 | Outdoor enclosures, pumps, solar and marine, communication cabinets | $0.18 – $0.31 |
| Nickel-plated brass, standard | Brass, nickel-plated | IP66 – IP68 | Switchgear, machine tools, outdoor industrial cabinets | $0.44 – $0.75 |
| Stainless steel 304 | 304 stainless steel | IP66 – IP68 | Food and beverage lines, washdown areas, general chemical plant | $0.98 – $1.55 |
| Stainless steel 316 | 316 stainless steel | IP66 – IP68 | Marine, offshore, coastal and chloride-rich chemical areas | $1.90 – $2.75 |
| EMC shielded | Brass, nickel-plated | IP67 – IP68 | VFD-driven motors, drives, data and instrumentation cabinets | $1.55 – $2.60 |
| Explosion-proof brass (ATEX / IECEx certified) | Brass | IP66 – IP68 + Ex | Oil and gas, chemical plant, Zone 1 and Zone 2 hazardous areas | $3.10 – $4.80 |
| Explosion-proof 316 stainless steel (certified) | 316 stainless steel | IP66 – IP68 + Ex | Offshore platforms, refineries, corrosive hazardous areas | $5.00 – $7.20 |
| Armoured brass | Brass | IP66 – IP68 | SWA and STA armoured cable, rail, heavy industry | $3.50 – $5.30 |
| Armoured 316 stainless steel | 316 stainless steel | IP66 – IP68 | Coastal and offshore armoured cable, tunnels, marine decks | $5.70 – $8.10 |
Price basis: the bands above are market price references for the M20 size in each gland family, indicative only, FOB Ningbo or Shanghai, US dollars per piece. They show what the market pays for an M20 gland in that family, not a quotation for a specific model or a price for every thread size. Minimum order is 200 pcs per size for brass and nylon families and 300 pcs per size for stainless steel and Ex-certified types; trial orders from 200 pcs are accepted on standard sizes.
Specific models and exact prices are quoted by our sales team. The same M20×1.5 thread in nickel-plated brass and in 316 stainless steel falls in two different bands, and the written price also depends on cable range, seal compound, thread length and whether a certificate pack is required. Send the model, thread and quantity through the quotation form and you receive a priced offer with lead time.
Documents and quotation
Material: Nickel-plated brass with NBR or EPDM seal. Working temperature: −40 °C to +120 °C. Full dimensional data for every size is in the parameter table above; the 2025 catalogue carries the same tables for the whole range, and the quotation form takes cable OD, thread and quantity.
Send cable OD, thread and quantity for a same-day price. Samples of 1 to 2 pieces are available for verification.
Request a Quote Now
Our team will get back to you within 24 hours.









