Brass cable gland, metric thread series M24 × 1.5 — clamping range 10–14 mm, panel cut-out 24.0–24.2 mm, thread length 9 mm, and a 24 mm body hex with a 27 mm locknut hex. Nickel-plated brass body, nylon clamping parts, nitrile seals.
M24 is bought for one reason: the cable is too big for the 12 mm top of the M20 bore, and M25 is not on the drawing. It is a working size rather than a common one, which is why it turns up in maintenance stores and on European machine drawings far more than in new greenfield designs.

M24, M25 and PG19 share a cable range — not a hole
Three sizes, one clamping range, one spanner, three different punches. If a gland has been ordered from a cable schedule that only lists “10–14 mm”, all three will look correct on paper.
| M24 × 1.5 | M25 × 1.5 | PG19 | |
|---|---|---|---|
| Thread O.D. | 24.0 mm | 25.0 mm | 25.0 mm |
| Panel cut-out | 24.0–24.2 mm | 25.0–25.2 mm | 25.0–25.2 mm |
| Cable range | 10–14 mm | 10–14 mm | 10–14 mm |
| Thread length GL | 9 mm | 9 mm | 9 mm |
| Spanner size | 24 / 27 mm | 24 / 27 mm | 24 / 27 mm |
Note that PG19 and M25 share the cut-out diameter but not the thread form. A 25.0 mm hole will accept either, and only the thread marking on the body tells you which one was specified — so read the old gland before ordering the replacement, not the drawing revision.
Where M24 is the right answer
- Sensor and actuator cables at 12–14 mm on machinery built to a metric drawing
- Replacement orders where the existing punch is 24.0 mm and M25 will not fit
- Applications needing the extra 2 mm of bore over M22 without stepping the panel up to 25 mm
If the cable is 14 mm or under and the panel is not yet drilled, M25 is the more available size and the same spanner. M24 earns its place when the hole already exists.
Parameter table — the sizes either side of M24
Neighbouring metric sizes are listed for substitution checks. The complete M14–M63 list, with cut-outs and thread lengths, is on the cable gland thread size chart.
| Model | Thread | Cable range (mm) | Thread O.D. (mm) | Mounting hole Ø (mm) | Thread length GL (mm) | Bonding length (mm) | Spanner size (mm) |
|---|---|---|---|---|---|---|---|
| M18-NP | M18 × 1.5 | 5–10 | 18 | 18.0–18.2 | 8 | 21 | 20 |
| M20-NP | M20 × 1.5 | 6–12 | 20 | 20.0–20.2 | 8 | 22 | 22 |
| M22-NP | M22 × 1.5 | 10–14 | 22 | 22.0–22.2 | 8 | 23 | 24 |
| M24-NP | M24 × 1.5 | 10–14 | 24 | 24.0–24.2 | 9 | 25 | 24/27 |
| M25-NP | M25 × 1.5 | 10–14 | 25 | 25.0–25.2 | 9 | 25 | 24/27 |
| M28-NP | M28 × 1.5 | 13–18 | 28 | 28.0–28.2 | 9 | 27 | 30 |
| M30-NP | M30 × 1.5 | 13–18 | 30 | 30.0–30.2 | 9 | 29 | 30/32 |
| M32-NP | M32 × 1.5 | 15–22 | 32 | 32.0–32.2 | 10 | 29 | 35 |
Spanner sizes are the width across flats and are listed as body / locknut where the two differ. At M24 the body is 24 mm and the locknut 27 mm, so a kit with one spanner will stop at the nut — see the spanner size chart.
Ordering and price basis
MOQ is 1,000 pcs per size for the standard nickel-plated brass version, with no mould or tooling charge. Trial orders of 100–500 pcs are accepted so the fit can be proved on a real panel. Thread length is the usual customisation: short thread for thin panels, long thread for thick ones, extended thread to drawing.
Documentation: CE declaration of conformity, RoHS and REACH statements, an IP68 test report to IEC 60529 for the assembly (2 m / 24 h as standard), and a material certificate covering the brass alloy and the nickel plating.
Send cable OD, thread and quantity for a same-day price. Samples of 1 to 2 pieces are available for verification.
Request a Quote Now
Our team will get back to you within 24 hours.








