A straight cable gland does one thing badly. It grips the sheath and seals the entry, and then it hands the cable back to the installer at exactly the point where the cable has to start bending. A 90 degree cable gland takes that turn into the fitting itself. The trade is simple and rarely stated: the elbow moves the bend from the inside of the enclosure, where space is scarce, to the outside, where height is scarce. Choosing one is deciding which of those two you can spare.
This guide covers when an elbow gland is the right fitting, what it costs in panel height, and the two numbers most often assumed rather than checked: the cable range and the tool clearance. It is about the fitting rather than the circuit; for the wider family see cable gland main types explained, and for the size bands of the straight nylon range see the جدول مقاسات غدة الكابلات النايلون.
An elbow gland is a straight thread with a moulded right angle body on top. It enters the enclosure like any other gland, seals on the face washer under the locknut, and compresses the sheath with a dome nut at the end of the arm. What it adds is a fixed internal turn: cable arrives vertically and leaves horizontally, in directions the fitting sets rather than the installer.
It does not add sealing or strain relief, and it does not make a tight bend acceptable. It relocates the bend to a place you can measure and a direction you can plan.
The dimension that decides whether an elbow fits is not the thread, it is the height above the panel face once installed. In this range it runs from 37 mm at the smallest size to 68 mm at the largest, and it grows faster than the thread does.
| Size | Cable range | Height above panel | Thread length GL | Spanner | Mounting hole |
|---|---|---|---|---|---|
| M16 | 4 to 8 mm | 37 mm | 8 mm | 19 mm | 16 to 16.3 mm |
| M18 | 5 to 10 mm | 39 mm | 8 mm | 22 mm | 18 to 18.3 mm |
| M20 | 6 to 12 mm | 43 mm | 9 mm | 24 mm | 20 to 20.3 mm |
| M22 | 10 to 14 mm | 48 mm | 10 mm | 27 mm | 22 to 22.3 mm |
| M25 | 13 to 18 mm | 56 mm | 11 mm | 33 mm | 25 to 25.3 mm |
| M32 | 18 to 25 mm | 68 mm | 11 mm | 41 / 42 mm | 32 to 32.3 mm |
Add the height to whatever the cable does next. An elbow pointing up on a cabinet top adds 43 mm at M20 before the cable has gone anywhere. On the underside the same fitting turns that cost into free space, which is why elbows are far more common on bottom and side faces.
Every cable has a minimum bend radius set by its manufacturer, and no gland changes it. What changes is whether you can see the bend. With a straight gland the first turn happens immediately past the dome nut, in whatever space the enclosure or the wall happens to leave, and the radius is whatever comes out of that. Nobody measures it, and the sheath is under compression on the inside of the bend at the exact point where the insert grips it.
An elbow replaces that improvised geometry with a moulded one. The turn has a defined radius and a defined direction, and the grip point sits upstream of it rather than inside it. The cable still needs its minimum radius after the arm, but by then the sheath is out of the gland and the radius is a cable-tray layout decision rather than a fitting decision.
Thread size does not travel between product families, and this is where most wrong orders start. At M32 the elbow covers 18 to 25 mm while the straight gland of the same thread covers 16 to 21 mm. A 25 mm cable needs an M32 elbow; the M32 straight gland will not grip it at all.
| الخيط | Elbow cable range | Straight gland cable range | Practical consequence |
|---|---|---|---|
| M20 | 6 to 12 mm | 6 to 12 mm | Interchangeable on cable; only the geometry differs |
| M22 | 10 to 14 mm | 10 to 14 mm | Interchangeable on cable |
| M25 | 13 to 18 mm | 13 to 18 mm, or 13 to 15 mm in the shorter body | Check which straight variant is on the drawing |
| M32 | 18 to 25 mm | 16 to 21 mm | Not interchangeable: the elbow reaches 4 mm higher |
Read it as a warning against substitution rather than a table to memorise: switching from straight to elbow at the same thread is safe at M20 and M22 and unsafe at M32. The thread is a hole dimension and the cable range is a seal dimension, set independently by whoever designed that body.
This elbow range stops at M32, which caps it at a 25 mm cable. There is no M40 elbow and nothing above it. A cable of 30 mm cannot be turned by this fitting at any thread size, and specifying “M40 elbow” on a requisition produces either a substitute or a delay.
The alternatives above M32 are a straight gland plus a bend in the tray or conduit downstream, a flexible gland that allows a gentler sweep, or a metal elbow from a different range if one exists for the duty. Each changes something: the conduit bend adds a joint to seal, the flexible gland gives radius without direction, and a metal elbow changes the material answer for corrosion and for temperature.
A straight gland loads its thread in tension along the axis. An elbow loads the same thread with a bending moment, because the cable’s weight and any pull act at the end of an arm rather than on the centre line. That moment arrives at a locknut which was chosen to resist a clamping force, not a lever.
Three things follow. A thin enclosure wall deflects under the moment and the face washer loses compression on one side, which shows up as a leak on the low side of the entry rather than all round. The moulded hole clearance is wider than a machined one, 0.3 mm in this range against 0.2 mm in the metal ranges, so the body can cock in the hole before the nut is fully tight. And the cable should be supported beyond the arm so that the gland is not the last restraint; that point is covered in cable gland strain relief.
The arm can be clocked to any of 360 degrees, but only while the body is still free to rotate. Once the locknut is tight the direction is fixed, so the sequence matters: thread the body in, set the arm to the cable route, hold that position, and only then run the locknut up. Tightening first and correcting afterwards scratches the bearing face and leaves the washer unevenly compressed.
Two checks before the locknut goes on. Confirm the arm clears the cable’s whole route, including the bend after the fitting rather than just the first straight run. And confirm a spanner will fit the dome nut at the end of the arm: at M32 that nut needs 41 to 42 mm of access on a fitting already 68 mm tall.
Sustained vibration is the clearest case against it. A moulded arm carrying cable mass is a cantilever, and a cantilever on a plastic thread is the geometry that loosens fastest; the mechanisms are set out in how to prevent cable glands from loosening. Where the joint will see continuous movement, a straight gland with the cable supported independently is more stable, whatever the routing gain.
Hazardous areas are the second case. An elbow is a different body from the straight item and needs its own certification for the protection concept and the gas group; an assembly cannot be built by swapping a certified straight body for an uncertified elbow on the same thread. If the area is classified, the starting point is selecting cable glands for hazardous areas.
Third, high pressure washdown. An elbow has more joints than a straight gland and each is a sealing path, so confirm the IP rating quoted applies to the elbow body itself and not to the straight item in the same range.
| Option | What it gives you | What it costs | Use it when |
|---|---|---|---|
| 90 degree elbow gland | A fixed turn at the entry point | Height above the panel, and a bending moment on the thread | Space is short inside the enclosure and the cable must run along the panel face |
| Straight gland plus tray bend | Any radius the tray can give | Space downstream, and a longer first run | The enclosure has room and the route is being planned anyway |
| Flexible gland | A sweep rather than a corner | Sealing depends on an elastomer that also takes the movement | The cable has to move, or the route curves continuously |
| Conduit or flexible conduit bend | Protection along the run, not just at the wall | An extra joint and an extra interface to seal | The cable is exposed between the enclosure and the next point |
| Field | What to state | Why |
|---|---|---|
| Thread and size | Metric thread with pitch, for example M25 x 1.5 | The bare size does not carry the pitch |
| Cable range | The measured sheath diameter, one figure | Elbow ranges differ from straight ranges at the same thread |
| Height budget | The clear space available above the panel | Decides whether the elbow or a straight gland can be used at all |
| Arm direction | Route direction, or “field adjustable” | Fixed-arm variants exist and cannot be clocked later |
| الختم | IP rating and the actual wet condition | Confirm the rating applies to the elbow body, not the straight item |
| Accessories | Locknut and washer as separate lines | The elbow’s offset load makes the locknut a structural part |
The elbow body itself is listed as the 90 degree elbow nylon cable gland, and the rest of the moulded family sits in the nylon cable gland range. Where the entry is straight and the question is really about the hole behind it, the figures are in the cable gland hole size chart.
Routing a cable along the enclosure face instead of straight out of it. It is chosen when the space inside the cabinet cannot accommodate the cable’s first bend, or when a straight gland would foul a wall, a door or another enclosure immediately outside.
No. It gives the bend a fixed radius and a fixed direction instead of an improvised one. The cable still has to meet its own minimum bend radius after the arm, and the fitting does not relax that limit.
Not in cable range. The elbow covers 18 to 25 mm and the straight gland 16 to 21 mm, so a 25 mm cable needs the elbow and an 18 mm cable can use either. Compare the ranges before substituting one for the other.
Only if that elbow body is itself certified for the protection concept, gas group and temperature class of the location. A certified straight gland cannot be swapped for an uncertified elbow on the same thread and remain compliant.
Usually because the offset load has cocked the body in the hole and unloaded part of the face washer. Check that the mounting hole is within tolerance, that the panel is stiff enough for the moment, and that the cable is supported beyond the arm.
An armoured cable gland must grip the armour, bond it to earth and seal the sheath. This guide covers armour types, BW / CW / E1W sealing stages, and how two cable diameters set the gland size.
قراءة المزيد
اكتشف غدد إدخال الكابلات المتينة المقاومة للماء مع تصنيف IP68 المصنوعة من النحاس النايلون أو الفولاذ المقاوم للصدأ للاستخدام الآمن في الهواء الطلق والاستخدام البحري
قراءة المزيد
304 and 316 stainless steel cable glands differ in one element. What molybdenum does at a pit, why the magnet test proves nothing, and which parts the certificate actually covers.
قراءة المزيد
