A cable gland arrives with a compliance pack that is usually one PDF of scanned pages, and the pages are not equally strong. Three of them are certificates in the everyday sense: a laboratory tested something and a named person signed for it. Two are the manufacturer declaring its own conformity. One is an audit of a factory’s management system that says nothing about the part in your hand. Buyers who read the pack as a single verdict either reject good goods or accept a document that will not survive their own customer’s audit.
Compliance documents fall into three tiers, and a document from a higher tier never substitutes for one from a lower tier. A factory holding ISO 9001 can still ship a gland that fails its own catalogue dimension, and a report proving IP68 says nothing about whether the brass is lead-free.
| Tier | Typical document | The question it answers | The question it cannot answer |
|---|---|---|---|
| System | ISO 9001 certificate | Whether the factory runs a controlled, audited process | Whether this batch meets the drawing |
| Product performance | IP68 test report, ATEX or IECEx certificate | Whether a sample of this design passed a defined test | Whether every unit off the line will pass |
| Product composition | EN 10204 2.2 or 3.1 material certificate | What the metal in this delivery actually is | What the finished gland measures |
| Substance | RoHS declaration, REACH statement | Which restricted substances are present, and at what level | Whether the gland seals, clamps or bonds |
The most common goods-in failure is not a missing document but a 3.1 requested and a 2.2 delivered, with nothing on either page to tell a receiving clerk which is which.
IEC 60529 defines the two digits separately. The 6 is dust tight. The 8 means continuous immersion, and it is the only water level in the standard where depth and duration are left open, to be agreed between manufacturer and user. Two glands can both be IP68 while one is rated for a rain-soaked junction box and the other for a flooded wet well.
| Field on the report | Why it decides the answer | Send it back if |
|---|---|---|
| Standard and edition | Labs test to IEC 60529 with its amendments; an undated reference cannot be tied to a method | The number appears only inside a catalogue table, with no report behind it |
| Depth | Pressure is linear: every 10 m of water adds about 1 bar above atmosphere | 8 is claimed with no depth stated |
| Duration | 30 minutes proves a splash line; it does not prove a permanently submerged joint | 30 minutes is quoted for a joint that will sit under water for years |
| Test configuration | The sample must be gland, cable, enclosure wall and tightening torque together | The sample is described as the gland on its own |
| Laboratory and accreditation | An ISO/IEC 17025 scope covering IEC 60529 makes the result defensible to a third party | There is no laboratory name, or no report number |
| Date | Inserts, seals and thread forms change; an undated report may describe a superseded design | Nothing on the document carries a date |
The immersion levels we test and supply are 1.5 m for 30 minutes, 2 m for 24 hours as the outdoor default, 5 m for 72 hours for marine and tunnel work, and 10 m for 168 hours on request. That is four different products at four price points, all legitimately called IP68.
A single immersion report covers a single configuration: one thread size, one clamping insert, one cable outside diameter, one wall thickness, one torque value. Buy the same gland in eleven sizes and you are buying ten extrapolations and one tested part. That is normal practice, provided the series table says which size was tested.
On submersible pumps, marine deck penetrations and tunnel sumps, where the gland is the only barrier, ask whether the report lists your size by name or carries the note “similar performance for other sizes”. If it is the second, request a size-specific report or witness the test.
EN 10204 defines inspection documents for metallic products and has two axes rather than one: whether the results come from testing the material in your delivery, and who is entitled to validate the page. Buyers assume a bigger number means more testing. It means more independence.
| النوع | الاسم | Tested on your delivery? | Validated by | What it can support |
|---|---|---|---|---|
| 2.1 | Declaration of compliance | No results at all | The manufacturer | A commercial statement that the order was met |
| 2.2 | Test report | No, results come from non-specific inspection | The manufacturer | “This grade generally measures what we say” |
| 3.1 | Inspection certificate | Yes, specific inspection of the supplied material | The manufacturer’s inspection representative, independent of production | A field-failure investigation months later |
| 3.2 | Inspection certificate, independently validated | Yes, specific inspection | As 3.1, plus the purchaser’s inspector or a designated body | A contract requiring third-party witnessing |
A second limitation applies to every gland. Traceability to a heat number is a property of a batch kept separate, not of a part. A brass bar carries its heat number; that bar becomes tens of thousands of bodies that go into a bin, and nothing short of segregating the whole run puts the number back on the individual piece. Part-level traceability must be agreed before production, because it changes how material is handled and it costs money. A supplier who answers “full traceability” without that qualification has told you something that cannot be true.
RoHS limits lead to 0.1 percent by weight in each homogeneous material. Free-cutting brass of the kind used for gland bodies, typically CuZn39Pb3 or CW617N, contains around 3 percent lead by design, because that is what makes the alloy machine cleanly at production speed. The part is legal only through Annex III exemption 6(c), which allows up to 4 percent lead in copper alloy, and under Delegated Directive (EU) 2025/2364 that exemption currently runs to 30 June 2027.
So a declaration reading only “RoHS compliant” is either describing a lead-free alloy or omitting the legal basis for the lead it contains. Ask which. A useful statement names the exemption, and a useful buyer treats the date as a re-approval cycle rather than a permanent permission. Where a design life runs past the current date, the question is what the supplier’s lead-free alternative is, not what the certificate says today.
Lead is also on the REACH Candidate List of substances of very high concern, which it joined in 2018. Above 0.1 percent by weight in an article, the supplier must tell the customer what is present and how to use it safely, and an EU supplier carries a SCIP notification obligation. The two documents arrive in the same envelope and answer different questions: RoHS restricts ten named substances in electrical and electronic equipment, REACH asks about substances of very high concern in any article.
The EU Declaration of Conformity is signed by the manufacturer under its sole responsibility. No laboratory issues it and it certifies nothing by itself. What makes it usable is detail: the directives cited, the harmonised standards with their versions, identification of the product by type or series, a signature and a date.
For a gland the usual set is the Low Voltage Directive where the assembly sits in a 50 to 1000 volt circuit, the EMC Directive for shielded versions forming part of a bonding path, and RoHS in every case. A declaration that says “CE compliant” and lists no standard versions is a letterhead with a logo on it. Which of them has been withdrawn is covered in our guide to cable gland standards.
For explosive atmospheres the document set changes shape. ATEX requires an EU-type examination certificate from a notified body plus a production module, either a quality assurance notification or product verification. IECEx uses a test report, a quality assessment report and a certificate of conformity, and the three are only meaningful together.
The part that decides your order is the schedule, which lists the variants covered and the thread sizes for each. A size added to the catalogue after issue is not covered until the certificate is varied, and a gland shipped outside its schedule is an uncertified gland with a certified logo on the box. In the marking, the four-digit number beside the CE mark belongs to the notified body and appears for categories 1 and 2; category 3 can be self-declared. Our comparison of ATEX and IECEx assessment routes covers how each system reaches its verdict.
ISO 9001 certifies that a quality management system has been audited. It does not certify the gland and is not a substitute for a test report on any characteristic. What it buys is change control: a documented route for revising a drawing, a record of nonconformities, and an audit trail when a dimension drifts between shipments.
This is the check we suggest running at goods-in. Most failures here are administrative rather than deceptive.
| What you see | What it means | What to do |
|---|---|---|
| “IP68” printed in a catalogue table only | A claim, not evidence | Request the report; read depth and duration before anything else |
| 3.1 ordered, 2.2 delivered | The results describe the mill’s general output, not your metal | Reject, or accept with a written deviation and a price adjustment |
| “RoHS compliant”, no exemption cited | Leaded brass declared without its legal basis | Ask for the exemption reference, or a lead-free alloy statement |
| Declaration of Conformity with no standard versions | A self-declaration with nothing traceable behind it | Ask for a revised declaration naming standards and editions |
| Ex schedule without your thread size | Your size is in the catalogue but not in the certification | Request a certificate variation, or buy only scheduled sizes |
| Every page undated | The documents cannot be tied to the design you bought | Ask for dated copies and file them with the purchase order |
Suppliers send the cheapest document that satisfies the word “certificate” because the request usually contains that word and nothing else. Six lines close the gap: the IP statement format including depth and duration; the EN 10204 type by number; the RoHS exemption citation; a REACH Article 33 statement; the Ex certificate schedule including your sizes; and the laboratory whose report will be supplied. None of it costs a supplier anything to answer, and all of it is checkable on arrival. It changes the quotation too, because a 3.2 certificate and a 2.1 are not the same price, and a 10 m immersion test is not a 2 m one.
It is a genuine data record, and it is what most development work runs on. Where the enclosure must pass a client audit, ask for a report from a laboratory accredited to ISO/IEC 17025 for IEC 60529 — that is the one that travels.
3.1 wherever the metal must be identifiable after the fact, which covers most industrial and marine work. 3.2 only where a third party must witness the testing. Specifying 3.2 to be safe adds cost and, more painfully, lead time while the inspector is arranged.
Yes for the Low Voltage, EMC and RoHS directives, which are self-declaration. ATEX is different: categories 1 and 2 need a notified body for the type examination, and its four-digit number sits beside the CE mark.
No. A supplier who sends one when you asked for the other has not answered you. RoHS restricts ten named substances in electrical equipment; REACH asks which substances of very high concern are present in an article.
Treat it as an immersion rating with unspecified conditions, which cannot be compared with another supplier’s claim. Ask for depth and duration in writing, and if no answer comes, buy on the lower assumption you can defend.
If you are assembling a documentation pack and need to know which of these we can supply for a given gland, the IP rating selection guide and our brass range are the fastest starting points. A note with your thread size and project standard is enough for us to answer with specifics.
هل عانيت من قبل في اختيار غدة الكابل المناسبة؟ لا تقلق - لست وحدك! قد تكون غدة الكابلات صغيرة، ولكنها تلعب دوراً رئيسياً في ضمان سلامة واستقرار أنظمتك الكهربائية. سواءً كنت تعمل في مجال الأتمتة الصناعية أو البتروكيماويات أو الهندسة البحرية، فإن اختيار غدة الكابلات الخاطئة يمكن أن يؤدي إلى تسرب المياه أو قصر [...].
قراءة المزيد
There is no HS heading for cable glands. Why the material decides the chapter, the four copper headings a brass gland can legally occupy, and what the wrong code costs at the border.
قراءة المزيد
304 and 316 stainless steel cable glands differ in one element. What molybdenum does at a pit, why the magnet test proves nothing, and which parts the certificate actually covers.
قراءة المزيد
