Presse-étoupe en laiton

Presse-étoupe en laiton nickelé étanche IP68 M36A*1.5

Ces presse-étoupes en laiton présentent une étanchéité exceptionnelle (conforme aux normes IP68/IP69K), une résistance aux acides, aux huiles, à l'exposition aux UV et au vieillissement, ce qui les rend adaptés aux environnements difficiles. Leur construction solide et leur haute résistance à la traction empêchent l'arrachement et la déconnexion des câbles, garantissant ainsi la sécurité et la stabilité des connexions.

Fil :Métrique | PG | G(PF) | NPT
Matériaux :Laiton nickelé, Nylon PA66
Joint et bague d'étanchéité :NBR
Niveau de protection :IP68
Température de travail :Statique : -40℃ à 100℃, jusqu'à 120℃ pendant une courte période.

Nickel-plated brass cable gland M36A × 1.5, IP68 — clamping range 18–25 mm, panel cut-out 36.0–36.2 mm, thread length 10 mm, 40 mm across flats, bonding length 31 mm.

M36 is the metric size that sits immediately under the 37 mm family, which makes it the one most often confused with M37 and with PG29. All three close on 18–25 mm cable and all three take a 40 mm spanner. Only the punch tells them apart.

Nickel-plated brass M36 cable gland marked M36x1.5 with hex body and locknut

M36, M37 and PG29: one millimetre, three part numbers

M36 × 1.5M37 × 1.5PG29
Filet O.D.36.0 mm37.0 mm37.0 mm
Panel cut-out36.0–36.2 mm37.0–37.2 mm37.0–37.2 mm
Cable range18–25 mm18–25 mm18–25 mm
Thread length GL10 mm10 mm11 mm
Spanner size40 mm40 mm40 mm

M37 and PG29 land on the same cut-out, so a 37.0 mm hole will accept either body. The thread marking is the only reliable difference on an unlabelled part — read the flat, and if it is worn, measure the thread outside diameter rather than the hole.

M36 is the odd one out: 36.0 mm is a punch that nothing else in this range uses. That makes it a size you order against a drawing rather than a size you substitute into an existing hole.

What IP68 covers on this gland

The IP68 rating is issued for the assembly, not for the body, and it is published in grades: 1.5 m for 30 minutes, 2 m for 24 hours as standard, 5 m for 72 hours and 10 m for 168 hours by special order. Specify the grade and the duration on the order — the label alone does not distinguish between them, and a gland rated for 2 m is not a gland rated for a flooded pit.

The limiting part is the insert, not the brass. An insert sized to the top of the clamping range has almost no compression left, which is why a 24.8 mm cable in a 25 mm bore is a worse joint than a 21 mm cable in the same gland.

Parameter table — the sizes either side of M36

Neighbouring rows are shown for substitution checks. Every metric and PG size we produce is on the thread size chart.

ModèleFilCable range (mm)Diamètre extérieur du filetage (mm)Mounting hole Ø (mm)Thread length GL (mm)Bonding length (mm)Taille de la clé (mm)
M28-NPM28 × 1.513–182828.0–28.292730
M30-NPM30 × 1.513–183030.0–30.292930/32
M32-NPM32 × 1.515–223232.0–32.2102935
M33-NPM33 × 1.515–223333.0–33.2102935
M36-NPM36 × 1.518–253636.0–36.2103140
M37-NPM37 × 1.518–253737.0–37.2103140
M40-NPM40 × 1.518–254040.0–40.2113140/45
M42-NPM42 × 1.522–304242.0–42.2113545

Ordering

MOQ is 1,000 pcs per size for standard nickel-plated brass, no tooling charge; trial orders of 100–500 pcs accepted. Long and extended thread lengths are made to order and quoted per drawing rather than per piece.

Documentation: CE declaration of conformity, RoHS and REACH statements, an IP68 test report to IEC 60529 for the assembly (2 m / 24 h as standard), and a material certificate covering the brass alloy and the nickel plating.

Send cable OD, thread and quantity for a same-day price. Samples of 1 to 2 pieces are available for verification.

Demander un devis maintenant

Notre équipe vous répondra dans les 24 heures.